Map: Natural Earth
Smart Hands
Smart Hands in Czech Republic
Smart hands is technical work that needs diagnostic judgement and configuration knowledge. Reboot Monkey engineers are dispatched to the customer's racks and work on the customer's own servers and network equipment, giving on-site IT support in Czech Republic data centers from the first request to the finished work.
8
of our services in Czech Republic
Choose your city
Services in Smart Hands
- Smart Hands
- Colocation
- Data Center Decommissioning
- Data Center Migration
- Rack and Stack
- Remote Hands
- Server Migration
- ITADon request
In depth
Smart Hands: 7 sections, open any to read more.
Smart Hands in Czech Republic: How It Works
Smart hands is technical work that needs diagnostic judgement and configuration knowledge. In Czech Republic it is carried out by Reboot Monkey engineers who are dispatched to the customer's rack. Reboot Monkey is a third-party datacenter services operator. It is not a hosting company and not a datacenter owner.
The facility operator owns and runs the building, including its power, cooling and access policy, and Reboot Monkey engineers work under the operator's site rules.
Smart hands is the request to make when the cause of a problem, or the exact steps of a change, are not known in advance. The engineer starts from the symptom or from the target configuration and works towards the cause or the result. For that reason a request should say what the equipment is doing, what it should be doing and where it sits in the rack. Where the task is a single physical action that the customer can specify step by step, remote hands is the better fit, and Reboot Monkey offers both. Reboot Monkey engineers carry out that work on the customer's own equipment, in the customer's facility, on the customer's instruction.
Smart hands covers the work inside the rack that needs judgement. The customer's description of the task sets its scope. Work that falls outside that description is agreed as a separate service with its own definition, so a fault investigation can lead to a component swap, a cabling job or a migration, each scoped on its own.
Four details are useful in a request. The first is the symptom in the customer's own terms, such as a device that does not boot or a port that shows no link, together with what has already been tried. The second is the identification of the equipment, since asset tags and rack positions are what an engineer reads on site. The third is any configuration change the customer has approved, so that the engineer applies the change the customer intended and not one inferred on site. The fourth is the outcome the customer expects, stated as a working state, for example a link that is up or a server that boots, because that is how the end of the job is recognised.
A smart hands request moves through four stages from first contact to finished work.
- Request: the customer describes the task, the site and the equipment concerned, with the rack position, serial number or asset tag of the device where these are known.
- Scope and quote: Reboot Monkey and the customer agree what the work covers. Prices are quoted on request and depend on the customer and the size of the job.
- Dispatch: a Reboot Monkey engineer is dispatched to the customer's facility in Czech Republic.
- Work: the engineer carries out the task in the customer's rack.
Datacenter Landscape in Czech Republic
Data centres in Czech Republic, ordered by the number of networks present:
- CE Colo Prague (CE Colo Czech s.r.o.), Nad Elektrarnou 1428/47, 10600 Prague: 152 networks; carriers 1-IX EU, Arelion, Core-Backbone, Global Network Management, Inter.link and others
- TTC TELEPORT DC1 (TTC Teleport s.r.o.), Tiskarska 10, 10000 Prague: 80 networks; carriers Core-Backbone and RETN
- TTC TELEPORT DC2 (TTC Teleport s.r.o.), Sazecska 10, Prague: 31 networks; carriers Nextremum
- GTS Telehouse Prague (GTS Novera, a.s.), Vinohradská 190, 13000 Prague: 17 networks
- DC Tower Zizkov CRa (Radiokomunikace, a.s.), Mahlerovy sady 1, 130 00 Prague: 16 networks; carriers Arelion
- Master DC Brno (Master Internet s.r.o.), Cejl 20, 60200 Brno: 7 networks; carriers RETN
- DC Coolhousing - Prague (Coolhousing s.r.o.), Vinohradská 2405/190, 130 00 Prague: 6 networks
- CE Colo DC7 Prague (CE Colo Czech s.r.o.), K Pérovně 1616/2, 102 00 Prague: 5 networks
- Casablanca INT s.r.o. (ACTIVE 24, s.r.o.), Vinohradská 184, 130 52 Prague: 5 networks
- Shiran Datacenter (FreeTel, s.r.o.), Luzna 716/2, 16000 Prague 6: 5 networks
Smart Hands by City
City pages for smart hands in Czech Republic:
- Prague: https://www.rebootmonkey.com/en/czech-republic/prague/smart-hands/
Smart Hands in Czech Republic: What We Deliver
Smart hands work often touches neighbouring services: a diagnosis ends in a component swap, a new device has to be racked and cabled, or a change requires the cabling to be checked. Reboot Monkey offers the following services alongside smart hands. Each has its own definition, and a request can name the one it needs.
Several services combine in one request. A new GPU or AI deployment starts with the rack and network design, continues with racking, cabling and node swaps, and ends with the design documented and handed over in a controlled way. An exit from a facility joins the physical move of the equipment to its new location with the removal and disposal of the retired hardware. Each part is scoped against its own definition.
- Remote hands: physical tasks carried out on the customer's instruction (reboots, cable checks, component swaps, visual checks). The customer specifies each action and the engineer performs it.
- Rack and stack: installing, mounting and cabling new hardware. Once a new device is cabled, configuring it is smart hands work where that needs configuration knowledge.
- Server migration: moving equipment between racks, rooms or facilities. Faults that appear after a move are diagnosed as smart hands work.
- Structured cabling: installing, labelling and patching the cabling between the customer's racks and network equipment. Cable checks the customer can specify are remote hands, while cabling installed, labelled and patched to a layout is structured cabling.
- Hardware monitoring: monitoring of the customer's servers and network equipment by the Reboot Monkey NOC. Monitoring is a separate service from the on-site work.
- Asset inventory: recording the customer's equipment in the data center by serial number, asset tag and rack position, against the customer's asset list. The same identifiers are what an engineer uses to find a device when a smart hands request arrives.
- GPU and AI cluster deployment: racking, cabling and node swaps. The GPU and AI deployment package is the same scope of racking, cabling and node swaps for a GPU or AI cluster.
- Hardware supply and spares: supply of data-centre hardware, servers, network equipment and spare parts, with spares kept in the customer's rack on request.
- Remote hands retainers and hour blocks: remote hands agreed as a retainer or as a block of hours for recurring work, with terms agreed per customer and quoted on request.
- Rack and network design: the rack layout and the network topology of a new or expanding deployment, ending with documentation of the design and a controlled handover.
- Multi-site rollouts: one installation programme carried out at several of the customer's sites by Reboot Monkey engineers.
- Data center decommissioning: removing and disposing of retired hardware.
- Datacenter exit and relocation: the physical move of the customer's equipment to its new location together with the removal and disposal of the hardware that is retired.
Why Reboot Monkey for Smart Hands in Czech Republic
For an IT director the practical question is how many parties a single change involves. Reboot Monkey sells rack space, IP transit, leased IP addresses, network, data-centre hardware and the services that deliver, install and support them, so a change that touches the rack, the circuit and the address space can be raised with one third-party operator.
Smart hands work often ends on the network side: a link that has to be patched, a circuit that has to be ordered, an address block that has to be assigned. Reboot Monkey sells the network for the rack: it orders the cross connects and carrier circuits from the facility operator and the carriers present in the facility, and Reboot Monkey engineers install and patch the cabling in the customer's rack. The ordering and the patching are handled by the same company. A request that begins as a smart hands visit can therefore include the circuit and the patching in one quote.
IP transit is offered as Economy, Premium and DDoS Premium plans, each quoted per data center for the capacity the customer needs. IPv4 addresses can be leased alone or together with IP transit and rack space under one agreement. Dark fibre between data centres and wavelength circuits are ordered from the carriers and quoted on request.
For customers who want the infrastructure bought and run for them, there is the IT infrastructure turnkey and run service. You or your investors fund the IT infrastructure. Reboot Monkey buys, installs, configures and then runs it for you, inside the data center you choose.
A second, briefed Reboot Monkey engineer is named as backup for every customer site. The backup is named per customer site. As of 2026, Reboot Monkey's field engineers work in 190 countries and more than 400 locations. When the task involves fibre, a fibre inspection scope and cleaning kit are available on request.
Requests are quoted against the service definitions: a task that needs diagnosis is smart hands, a task the customer can dictate action by action is remote hands, and equipment moving between racks, rooms or facilities is server migration.
A quote request is simplest to scope when it states five things.
- the service, named by its definition, for example smart hands or remote hands;
- the site in Czech Republic and the equipment concerned;
- whether the work is a single job or recurring, since recurring remote hands can be agreed as a retainer or a block of hours;
- the outcome the customer expects when the job is finished;
- any network element, such as a cross connect, an IP transit plan or leased IPv4 addresses, that belongs to the same piece of work.
How Reboot Monkey Works
These terms apply in every facility in Czech Republic where Reboot Monkey engineers work.
- Response: 1-hour, around-the-clock incident response SLA, and a 15 minute premium response available where technicians are stationed on-site, as a paid add-on. The incident response SLA covers incidents and unplanned requests; on-site, dispatch and resolution times, priority tiers, and planned or scheduled work are agreed per site in the service agreement.
- Monitoring: 24/7 NOC monitoring across all facilities, covering IPMI, iDRAC, SNMP, temperature, power, network signals.
- Hardware: vendor-neutral technicians for Dell, HP, Cisco, Juniper and Arista equipment.
- Independence: independent from facility operators (not Equinix SmartHands, not NTT staff).
- One agreement: single provider across cities, so a customer in several cities needs only one agreement.
- Service levels and terms: https://www.rebootmonkey.com/en/solutions/sla
- Published case study: a major ICT provider engaged Reboot Monkey for three full infrastructure rollouts in Lahore, Karachi and Islamabad, with the hardware installed the same day at every site. Read the case study at https://www.rebootmonkey.com/en/resources/case-study/how-we-completed-3-full-deployments-across-pakistan
Smart Hands
The data centres we work in hold their own certifications, such as ISO/IEC 27001 and ISO 9001. Ask us for the certificate of your site.
Frequently Asked Questions
Smart Hands vs. Remote Hands | What's the Difference?
Remote hands are physical tasks carried out on the customer's instruction, such as reboots, cable checks, component swaps and visual checks. Smart hands is technical work that needs diagnostic judgement and configuration knowledge. The difference lies in who decides the steps: with remote hands the customer specifies each action, with smart hands the engineer works out what to do. Reboot Monkey offers both, and remote hands can also be agreed as a retainer or a block of hours.
What does smart hands cover in Czech Republic?
In Czech Republic, smart hands covers technical work that needs diagnostic judgement and configuration knowledge, carried out in the customer's rack by a Reboot Monkey engineer. Neighbouring work is scoped as its own service: rack and stack, server migration, structured cabling, asset inventory and GPU or AI cluster racking, cabling and node swaps. Each is scoped against its own definition.
Do you provide on-site IT support in Czech Republic data centers?
Yes. Reboot Monkey engineers are dispatched to the customer's equipment in Czech Republic data centers and carry out the work in the customer's rack. A request states the task, the site and the equipment, the scope is agreed, and an engineer is dispatched; a second, briefed engineer is named as backup for every customer site. Prices are quoted on request and depend on the customer and the size of the job.
Do you work in every datacenter in Czech Republic?
Reboot Monkey engineers work in any facility in Czech Republic where the customer has equipment and access, under the operator's own access and safety rules. The customer adds the engineers to the facility's access list before the first visit.
How fast can Reboot Monkey respond in Czech Republic?
Incidents and unplanned requests are handled under a 1-hour, around-the-clock incident response SLA. There is also a 15 minute premium response available where technicians are stationed on-site, as a paid add-on. On-site, dispatch and resolution times, priority tiers, and planned or scheduled work are agreed per site in the service agreement.
How is Reboot Monkey different from the facility operator's own staff?
Facility operators' own technicians work for the building. Reboot Monkey engineers work for the customer: they are independent from facility operators (not Equinix SmartHands, not NTT staff), follow the customer's instructions, and the same team can cover several buildings in the country under one agreement.
How do I get started with smart hands in Czech Republic?
Send the site, the equipment and the task through the contact form. Reboot Monkey replies with a quote and an engineer plan for that facility. Once agreed, the customer adds the engineers to the facility's access list and the smart hands work is scheduled under the operator's rules.
Cities we cover in Czech Republic
Request Smart Hands in Czech Republic
Describe the task, the site and the equipment, and Reboot Monkey will quote the work.